Friday, January 11, 2013

LTE DRIVE TEST PARAMETERS

RSRP :- Reference signal receive power.
•      RSRP (dBm) = RSSI (dBm) -10*log (12*N)

where RSSI = Received Signal Strength Indicator
             N: number of RBs across the RSSI is measured and depends on the BW

Significance :
RSRP is the most basic of the UE physical layer measurements and is the linear average power (in watts) of the downlink reference signals (RS) across the channel bandwidth for the Resource elements that carry cell specific Reference Signals. 

Knowledge of absolute RSRP provides the UE with essential information about the strength of cells from which path loss can be calculated and used in the algorithms for determining the optimum power settings for operating the network. Reference signal receive power is used both in idle and connected states
Range :-  -44 to -140 dBm

•      RSRP term is used for coverage same as RSCP in 3G

RSRQ :Reference signal receive quality

RSRQ = RSRP / (RSSI / N)

N is the number of resource blocks over which the RSSI is measured

RSSI is wide band power, including intra cell power, interference and noise.

Significance :- 
 It provides the Indication of Signal Quality . Measuring RSRQ becomes particularly important near the cell edge when  decisions need to be made, regardless of absolute RSRP, to perform a handover to the next cell. Reference signal receive quality is used only during connected states

Range :-  -3 to -19.5 dB
      RSRQ term is used for Quality same as Ec/No in 3G.
•      SINR :- Signal to Noise Ratio.
SINR = S / I + N
             
               S -- Average Received Signal Power
                I  --  Average Interference power
                N --  Noise Power

Significance  : Is a way to measure the Quality of LTE Wireless Connections. As the energy of signal fades with distance i.e Path Loss due to environmental parameters ( e.g. background noise , interfering strength of other simultaneous transmission)

•      RSSI :- Received Signal Strength Indicator.
    RSSI = wideband power = noise + serving cell power + interference power
     RSSI=12*N*RSRP
     RSSI per resource block is measured over 12 resource elements.
N: number of RBs across the RSSI is measured and depends on the BW
Based on the above:
                                
RSRP (dBm) = RSSI (dBm) -10*log (12*N)

      Significance :– 
       Is the parameter represents the entire received power including the wanted power from the serving cell as well as all the co channel power & other sources of noise

     CQI :- Channel Quality Indicator
     Range :- 1 to 15
                 
        Significance:
       CQI is a measurement of the communication quality of wireless channels i.e. it indicates the downlink mobile radio channel quality as experienced by the UE .CQI can be a value representing a measure of channel quality for a given channel. Typically, a high value CQI is indicative of a channel with high quality and vice versa.
•      CQI is measured in the Dedicated mode only.
•    CQI depends on the RF conditions.
    Better the CQI better the throughput will get and vice versa.
•    PCI :- Physical Cell Id
      Range :- 0 to 503
    Significance - PCI used to identify the cell & is used to transmit the data
       PCI = PSS + 3*SSS
               PSS is Primary Synchronization Signal ( Identifies Cell Id  ).
               PSS value can be 0, 1 & 2
               SSS is Secondary Synchronization Signal ( identifies Cell Id
               group).
               SSS value can be 0 to 167.

    BLER :- Block Error Rate
•    Block Error Ratio is defined as the ratio of the number of erroneous   blocks received to the total number of blocks transmitted
     Significance - 
        A simple method by which a UE can choose an appropriate CQI value could be based on a set of Block Error Rate (BLER) thresholds . The UE would report the CQI value corresponding to the Modulation Coding Schemes that ensures  BLER ≤ 10% based on the measured received signal quality
•    BLER is Calculated using Cyclic Redundancy error Checking method
      High BLER leads to loss of Peak rates & efficiency
      BLER  threshold should be low i.e. ≤ 10%
  
     
DDownlink Throughput
-I    n E-UTRAN  may use a maximum of 2 Tx antennas at the ENodeB and 
       2 Rx antennas at the UE ( MIMO ).
   Significance - Target for averaged user throughput per MHz, 3 to 4 times
   Release 6 HSDPA i.e Higher user throughput as compared to 3G ( Over 300 Mbps downlink as compared to 14 Mbps in UMTS)
-    The supported user throughput should scale with the spectrum
      bandwidth.

    Uplink Throughput
-I  n E-UTRAN uses  a maximum of a single Tx antenna at the UE and 2 Rx
    antennas at the E Node B.
 -  Greater user throughput should be achievable using multiple Tx
     antennas at the UE ( MIMO )
.
-  Significance- 
    Target for averaged user throughput per MHz, 2 to 3 times Release 6 Enhanced Uplink i.e Higher user throughput as compared to 3G (Over 50 Mbps Uplink as compared to 5.76 Mbps in UMTS).The user throughput should scale with the spectrum bandwidth provided that the maximum transmit power is also scaled.

12 comments:

Debashis said...

Dear Dharmendra,
Thank you so much for this useful information. May God bless you!

IBS said...

Welcome Dear............

Unknown said...

Sir i need more parameters about 2G,3G,4G LTE.PLZ help me in this matter

Unknown said...

Thank you so much for this useful information.i need more LTE optimization basic parameter.

Unknown said...

Thanks for telecom blog more information our sites
rf services

Rajesh said...

Thankyou sir. Can you pls provide me 4g drive test materials. like scft drive test and all.....
Email id - jmdrajeshswami@gmail.com

Thanks in Advance

Unknown said...

Thanks

Anonymous said...

Thank you so much

Unknown said...

Thanks sir

Unknown said...

Thank you sir

Unknown said...

Thank you sir

Shakuntla Singh said...

Thanku Sir . .